Drain syphon SY1: For the rapid draining of baths.Heat exchange coil CW5: For use with precision and general purpose stirred baths. Temperature range 2 °C above coolant temperature. Coil diameter/l mm 77/55, pipe bore inlet/outlet 7mm.PP spheres PS20: Between operating temperatures 60 °C and 100 °C and below room temperature a lid or layers of polypropylene spheres can be used. Above 100 °C a lid must be used.

Versatile system for the laboratory, with a comprehensive specification to suit most low temperature applications.Optima™ digital thermostat for precise temperature control: assembled with TX 150Cooling/heating range -30 to 100 °CStability ± 0.1 °CPowerful integral pump; allows temperature-controlled fluid to be circulated to external devices (18 L / min, 310 mbar)Easy to use rotary dial and two function keysClear 4 digit display - easy to read from a distance for instant reassuranceVisual alarm and countdown timer; alerts you when your attention is requiredUser calibration facility for optimum accuracy at the required operating temperatureOperating setpoint plus 3 adjustable preset temperatures for convenienceLiquid protection and over-temperature cut-outEasy access to coolant reservoir for local cooling of tubes, bottles etc.Powerful efficient cooling, ozone-friendly refrigerantDual-position bridge plate, ensures visibility/accessibility of the thermostat whilst optimising bench spaceRobust construction, corrosion resistant materials, stainless steel tank; durable in demanding environments5 °C thermostat on/off switch; stops tank freezing when operating with water

Consisting of two models, all products in the LT ecocool range are supplied assembled as ready to use kits, complete with accessory hosing, clips and connectors as standard.Choice of two models, temperature range -25 °C to 150 °C (model dependent)Industry leading 4 year warranty with Grant renowned service and support, no registration requiredActive cooling through the whole temperature rangeTrue energy saving of up to 80% against standard compressor unitsThermostat and chiller work in harmony, neither will operate alone, eliminating any danger of overheating or freezingSingle front switch for user convenienceModern, sleek, attractive design

Set of rings H 240: To cover the heating bath.Intermediate base H 159: Allows insertion of vessels into the bath, without affecting the stirrer motion.

*Temperature range: -20 to +140°C (max. 6 bar at +140°C)**Temperature range: -60 to +200°C (max. 20 bar at +175°C)

Test Tube Rack: Stainless steel, test tube rack, with 100 x 18mm diameter apertures.Support Rod: Stainless steel support rod, 316 x 12mm length x diameter.

Flat lid for unstirred water baths. With ring sets of variable hole diameter to accommodate tall vessels whilst reducing evaporation.

The base tray can be equipped with spring clamps of different sizes and used for tempering Erlenmeyer flasks in shaking water baths.Please order spring clamps for fastening Erlenmeyer flasks separately.

An ideal choice for schools and colleges requiring a basic simple-to-use quality water bath. Base tray included as standard. A great value range consisting of three models.Ambient + 5 °C to 95 °CUnique Set and Forget™ technology, fast heat-up, reliable temperature controlStability ± 0.5 °CSimple, intuitive controls, quick and easy to set temperaturePractical front panel lock, disables front panel controls preventing unintentional temperature changes3 year warrantyAccessory polypropylene spheres or a lid must be used at temperatures between +60 °C and +99 °C. Please order lid and PP spheres separately.

Prevents premature rusting and the growth of algae. Ideal for use in circulators, water baths, shaking water baths or heating baths. For routine applications from 5 to 90 °C.

Use:BUDDE heating bath liquid can be used continuously as a heating medium up to approx. 170 °C. Higher temperatures (below flash point) are possible, but will result in rapid darkening. The low pour point allows the bath liquid also to be used as a cooling medium. Mixtures with 10 % to 30 % water achieve best results.The crucial advantages of BUDDE heating bath liquid compared tothe oils or other organic liquid mainly used are:accidental spillage of water into the bath does not lead to dangerous spitting at temperatures over 100 °C, as the water dissolves in the heating bath liquid and subsequently evaporates safelyBUDDE heating bath liquid can easily be rinsed away with water which eases cleaning of laboratory equipment, e.g. distillation flasks, and also bench or floor if the bath liquid is accidentally spilled.BUDDE heating bath liquid does not foam when mixed with water.Viscosity on addition of water:BUDDE heating bath liquid is quite viscous at ambient or low temperatures, and therefore sometimes difficult to dispense. The addition of 10-20 % water reduces the viscosity and enables easier handling. If the mixture is then heated to 100 °C, the water evaporates without boiling. Further heating is only shortly delayed by this. Before next heating, water can be added again.Water solubility: BUDDE heating bath liquid can be mixed with water in any ratio. The hardness of the water has no effect on the bath liquid.Chemical character:Appearance:Clear, colourless or lightly yellowish liquidStorage time:When stored for long periods (over 2 years) the product may become darker. This does not affect the performance of the product.Water solubility:Heating bath liquid BUDDE can be mixed with water in any ratio.pH value (DIN ISO 976) :6-8 (100 g/l, 20 °C)Solidification temperature (DIN ISO 3016):approx. -39 °CBoiling point:200 °CDensity (DIN 51757, 23 °C):approx. 1.13 g/cm³ to 1.17 g/cm³Flashpoint (DIN EN ISO 2592): 290 °CIgnition temperature (DIN 51794):approx. 390 °C

DURAN®. For heating and cooling liquids. Thermostatting liquid is circulating between the double walls of the beaker jacket. With glass-screw connections GL14 with PTFE olives (O.D. 9mm, T-GL2000 with GL18 and O.D. 11mm) for thermostat hoses. Coolant ram pressure: 0.5bar at maximum, operating temperature: +120°C at maximum. Special sizes available on request.

We offer special air cooled circulator for the Beer Force-Ageing-Test. It is equipped with a programmer for the change between 0 °C / 40 °C and 0 °C / 60 °C in a 24 hour cycle. Casings and bath parts are made of stainless steel.Dimensions (W x D x H):

These powerful, low-temperature chillers are well matched for use with rotary evaporators, vacuum systems, spectrometers, and other analytical equipment. They also are available with a mobile cart accessory for convenient placement under a bench.Large, easy to read LED displaySpace-saving designCooling at ambient temperatures as high as 35°CTemperature Stability ±0.1 °CLow flow shut-off and alarm, high and low temperature alarmsFront mounted fluid level gaugeSimple setup, operation, and maintenanceChoice of pumps

Thanks to the adjustable stainless steel bridge the thermostats can be used with bath tanks up to a filling volume of 100 litres and bath widths from 33 to 68 cm.Simple control of complex applicationsInfinitely adjustable, extremely powerful pressure and suction pumpLarge, high-resolution TFT touch display with multilingual user interfaceMedium-contacting parts made of stainless steelIntegrated programmerExternal Pt100 connectionUSB interfaceRS232 interfaceEthernet interfaceAnalogue interfaces (optionally)Classification III according to DIN 12876-1Specifications:Temperature stability:± 0.01 °CFlow rate:16 ... 31 l / minPump pressure:0.24 ... 0.92 barSuction pressure:0.03 ... 0.4 barImmersion depth:150 mm // 200 mmHeating capacity:2000 W // 3000 WPermissible ambient temperature:5 ... 40 °CPower supply:230 V / 50 ... 60 Hz

Stable and reliable cooling for many common heat removal applications, including laser etching, AA furnaces, ICP, rotary evaporators, vacuum systems, reaction vessels, plasma etching, and condenser cooling. The chillers are available with turbine or positive displacement pump.A bright, full-color touchscreen displayCooling at ambient temperatures up to 30°CDynamicFilter™ self-cleaning filter systemLiquid level sensorUV light system to prevent growth inhibitorsUser-adjustable temperature, pressure, and flow rate alarmsExternal temperature tracking and communications capability (optionally)Cool Command™WhisperCool® noise reduction systemSelf-diagnostics service and functionality systemFront fill reservoir4 Casters, 2 of them lockingSpecifications:Working temperature:-10 ... 70 °CTemperatur stability:± 0.1 °CCooling capacity:850 ... 2900 WConnectivity:RS232, status relay, dry contactPower supply:240 V, 50 Hz

Recirculating chiller operates/works with Peltier technology, i.e. free of refrigerants and therefore environmentally friendly and maintenance-free.Large, bright OLED displaySimple operation with menu navigationSimultaneous display of set point, internal temperature, Tmin and TmaxUSB and RS232 interfacesAutostart function for power failureScope of supply: Chiller Piccolo 280 OLÉ, connector with hose barbTemperature range:Temperature stability:± 0.2 °CFlow rate:1.85 l/minPressure:0.95 barHeating power:0.7 kWCooling capacity (at 20 °C):0.28 kWDimensions (W x D x H):215 x 310 x 312 mmWeight:13 kgPower supply:100 ... 240 V, 50/60 HzIP code:IP 20

Many applications depend on a reliable source of cooling. Circulating chillers in the Unichiller range offer an ideal solution for environmentally friendly and economical cooling in laboratory and industry. There are over 50 air and water cooled models to choose from, with cooling powers from 0.3 to 50 kW. Efficient energy management in all Huber chillers ensures low operating costs and reduced usage of valuable fresh water. Huber circulating chillers are a resource saving solution with a quick return on investment.Options on request: heating, natural refrigerant, externally open applications, winter option, outdoor setup.

Many applications depend on a reliable source of cooling. Circulating chillers in the Unichiller range offer an ideal solution for environmentally friendly and economical cooling in laboratory and industry. There are over 50 air and water cooled models to choose from, with cooling powers from 0.3 to 50 kW. Efficient energy management in all Huber chillers ensures low operating costs and reduced usage of valuable fresh water. Huber circulating chillers are a resource saving solution with a quick return on investment.Options on request: heating, natural refrigerant, externally open applications, winter option, outdoor setup.

Small, robust and cost effective with its stainless steel casing. The Minichiller is the smallest Unichiller in the world. Minichillers are available with air or water-cooled refrigeration systems, illuminated level indicator, overflow and drain on the front. The filling port is on the top of the unit. All models use natural refrigerants as standard. Minichillers have suction and pressure pumps and therefore have the advantage of have a high flow at low pressure. This is particularly interesting for all pressure sensitive applications (e.g. glass condensors).Supply req.:* Permissible temperature in return line 80 °C

The PT31 circulation thermostat is equipped with high performance functions. The device is ideally suited for applications requiring a temperature range at a constant level. The robust locking mechanism of the PT31 provides a sturdy connection and ensures constant temperature control of the medium.Temperature control using Peltier technologySpace-saving, sturdy designSuitable for operation with non-flammable liquids (water or water/glycol mixture)SpecificationsTemperature range:8 ... 35 °CAccuracy: Resolution:±0.2 °C 0.1 °CPump performance: Max. pump pressure:20 l/h 20 mbarCooling power: Heating power:20 W 30 WPower supply:100 ... 240 V AC, 50/60 Hz, 1.3 ADimensions (W x D x H): Weight:108 x 145 x 199 mm 1.5 kg